Witch Reader

 

 
 
Products Used

Bisque
  • MB-102 Coupe Dinner Plate
Color
  • SC-6 Sunkissed
  • SC-13 Grapel
  • SC-23 Jack O' Lantern
  • SC-41 Brown Cow
  • SC-51 Poo Bear
  • SC-53 Purple Haze
  • SC-74 Hot Tamale
  • SC-83 Tip Taupe
  • FN-003 Orange
  • SG-401 Black Designer Liner
  • S--2101 Crystal CLear Brushing
Decorating Accessories
  • CB-110 #10/0 Liner
  • CB-200 #0 Detail
  • CB-404 #4 Pointed Round
  • CB-604 #4 Soft Fan
  • RB-104 #4 Liner
  • BT-910 Synthetic Sponge
  • AC-230 Clay Carbon Paper
Flying_Witch
 
 
Additional Materials
 
Project Info
  • Designer: Adena Griffith
  • Skill Level: Intermediate
  • Time: 2 hours
 

Instructions

  1. Begin with properly fired shelf cone 04 bisque.  Moisten a clean sponge and wipe bisque to remove any dust.
  2. With a Pencil and AC-230 Clay Carbon Paper, trace on the pattern.
  3. Use SG-401 Black Designer Liner to outline the whole design.
  4. Using a CB-200 #2 Detail Liner, apply SC-83 Tip Taupe to the hat. The ribbon on the hat is SC-53 Purple Haze.
  5. Using a RB-104 #4 Liner, apply SC-15 Tuxedo to the hair of the witch.
  6. Using a RB-104 #4 Liner, apply SC-13 Grapel to the cape and SC-53 Purple Haze to the dress area of the witch. Blend the two colors together when meeting them.
  7. Using a RB-104 #4 Liner, apply SC-41 Brown Cow to the stick of the broom and SC-51 Poo Bear to the bottom of the broom.
  8. Using a CB-110 #10/0 Liner, apply SC-74 Hot Tamale to the band on the broom.
  9. Using a CB-110 #10/0 Liner, apply start to fill in the stripes of her leggings with SC-53 Purple Haze and SC-23 Jack O’ Lantern and the long sleeve shirt with SC-74 Hot Tamale and SC-23 Jack O’ Lantern. Alternate between two colors.
  10. Moving onto her face and hands.  Using a CB-200 #0 Detail Liner, apply SC-74 Hot Tamale add a touch of water to the color. Use this to glaze her cheeks. Make sure to use the lighter tone on the highlights of her face. If you get to much glaze add a little water to your brush and move over the color. Be very careful during this step is can quickly turn muddy in the color if the black designer liner gets mixed in.
  11. Her lips are straight SC-74 without the water added to it.
  12. Using a CB-110 #10/0 Liner, apply SC-53 Purple Haze to the eyes
  13. Using a CB-404 #4 Pointed Round, apply SC-6 Sunkissed to the moon.
  14. If there are any parts that you may have gone over the SG-401 Black Designer Liner with a color, you may fix that now. Just squeeze some of the SG-401 Black Designer Liner onto a palette and dip your brush into some water, pull the brush through the edge of the SG-401 Black Designer Liner. This should give a small amount that you can go over any part that has had color over it.
  15. For the background of the piece. On a palette, squeeze out a small amount of SC-53 Purple Haze, SC-23 Jack O’ Lantern, and SC-6 Sunkissed. Choose which color you would like to start with and tap your sponge into it. Tap off some of the extra and then apply it to the plate. Keep adding color until it is to your liking. Then start to layer the three Stroke and Coats colors until you have the desired effect.
  16. Allow the plate is completely dry.
  17. Using a CB-604 #4 Soft Fan, apply 2 coats of S-2101Crystal Clear Brushing to the entire plate. Allow to dry.
  18. Using a CB-604 #4 Soft Fan, apply 3 coats of FN-003 Orange to the back of the plate. Allow to dry.
  19. Stilt and fire to shelf cone 06/05.

Who We Are

Our purpose, history, and policies

About Us

Site Map

Warranty & Freeze Policy

Where To Buy

Find the best place to purchase Mayco products

Dealers & Retailers

Distributors

PYOP & Ceramic Studios 

Project Library

Step by Step Instructions from the Professionals at Mayco.

Project library

New Projects