Flower Print Canvas

FlowerPrint

Products Used

Bisque
  • MB-1353 8" x 10" Clay Canvas
Color
  • SC-28 Blue Isle
  • SC-77 Glo-Worm
  • SC-13 Grapel
  • SC-15 Tuxedo
  • SG-401 Black
  • SG-403 Red
  • SG-405 Green
  • S-2101 Crystal Clear

Decorating Accessories

  • CB-604 #4 Soft Fan
  • DR01 Xiem Textured Rib
  • AR09 Xiem Textured Art Roller NamiWaves

Additional Materials

  • Sponge
  • 8" x 10" Gelli Printing Plate (www.gelliarts.com)
  • Liquid Dish Soap
  • Brayer Roller
  • 8" x 10" piece of Bubble Wrap
  • Download and print: Pattern
 

Designer: Laura Fraedrich
 

Instructions

  1. Begin with properly fired shelf cone 04 bisque. Moisten a clean sponge and wipe bisque to remove any dust.
  2. Mix each color of Stroke and Coat™ with 1/2 teaspoon of liquid dish soap. Mix well.
  3. With the soap mixed SC-77 Glo-Worm, pour 2-3 quarter-sized amounts onto the Gelli Printing Plate. Using the Brayer Roller, evenly roll out a thin layer of glaze, covering the entire plate.
  4. On top of the Gelli Printing Plate, lay the 8" x 10" piece of bubble wrap. Gently press bubble wrap into layer of glaze. Lift and remove bubble wrap.
  5. Place the Gelli Printing Plate, glaze side down, on top of MB-1353 Clay Canvas bisque. Firmly press printing plate to transfer glaze to bisque. Remove Gelli Printing Plate.
  6. With the soap mixed SC-28 Blue Isle, pour 2-3 quarter-sized amounts onto the Gelli Printing Plate. Using the Brayer Roller, evenly roll out a thin layer of glaze, covering the entire plate.
    • Note: The Gelli Printing Plate or Brayer does not need to be cleaned between layers.
  7. Using AR09 Xiem Textured Art Roller NamiWaves, roll through SC-28 blue Isle on top of Gelli Printing Plate.
  8. Place the Gelli Printing Plate, glaze side down, on top of MB-1353 Clay Canvas bisque. Firmly press printing plate to transfer glaze to bisque. Remove Gelli Printing Plate.
  9. With the soap mixed SC-13 Grapel, pour 2-3 quarter-sized amounts onto the Gelli Printing Plate. Using the Brayer Roller, evenly roll out a thin layer of glaze, covering the entire plate.
  10. Starting at the top of the Gelli Printing Plate, gradually guide the DR01 Xiem Texture Rib to make "S" strokes.
    • Tip: Use various sides of the DR01 Xiem Texture Rib to create different designs in the glaze.
  11. Place the Gelli Printing Plate, glaze side down, on top of the MB-1353 Clay Canvas bisque. Firmly press printing plate to transfer glaze to bisque. Remove Gelli Printing Plate.
  12. With the soap mixed SC-15 Tuxedo, pour 2-3 quarter-sized amounts onto the Gelli Printing Plate. Using the Brayer Roller, evenly roll out a thin layer of glaze, covering the entire plate.
  13. With the Gelli Printing Plate on the table, press the sides of the bisque onto the SC-15 Tuxedo covered printing plate. Roll out more SC-15 Tuxedo if needed.
  14. Using water and a small amount of dish soap, wash the Gelli Printing Plate.
  15. Place the flower pattern underneath the Gelli Printing Plate to use as a guide.
  16. On the Gelli Printing Plate, gently squeeze SG-403 Red, SG-408 Orange, and SG-405 Green, without the applicator tip, where colors are indicated.
  17. Place the Gelli Printing Plate, glaze side down, on top of the MB-1353 Clay Canvas bisque. Firmly press printing plate to transfer glaze to bisque.
  18. Using SG-201 Black, with applicator tip, outline petals and center area of flower to accentuate. Allow to dry.
  19. Using CB-604 Soft Fan, apply S-2101 Crystal Clear to top and sides of bisque.
  20. Fire to cone 06/05.

Who We Are

Our purpose, history, and policies

About Us

Site Map

Warranty & Freeze Policy

Where To Buy

Find the best place to purchase Mayco products

Dealers & Retailers

Distributors

PYOP & Ceramic Studios 

Contact Us

 (614) 876-1171 |   (614) 876-9904

info@maycocolors.com

Technical Support

614-675-2031

technical@maycocolors.com

custom-css-security